Telecom Power & Energy
Plan site load, rectifier capacity, battery autonomy, generator fuel and solar support as connected parts of a telecom power system.
Start Here
Use the workflow below when planning or reviewing a telecom site power system. Begin with a measured DC load, then size conversion, storage and backup in sequence.
- Read the rectifier sizing guide to establish load, recharge and N-1 assumptions.
- Size rectifiers, then check battery autonomy and backup fuel.
- Validate equipment limits, battery age, generator operating rules and site measurements before approval.
Calculate and Plan
- Telecom rectifier sizing — capacity, recharge and N-1 check.
- -48 V battery runtime calculator — autonomy under the stated load.
- Generator fuel consumption and runtime calculator — backup duration and fuel use.
- Telecom solar and battery sizing — solar contribution and storage sizing.
Worked example: rectifier current then 4-hour battery
Cross-check with the telecom rectifier calculator and the -48 V battery runtime calculator. Rectifier numbers follow the published 180 A guide example.
1. Inputs and assumptions
| Input | Value | Assumption |
|---|---|---|
| DC load | 180 A @ −48 V | Measured/defined site load boundary |
| Battery recharge | 60 A | Steady recharge current after utility restore |
| Headroom / growth / recharge peak | 15% / 15% / 25% | Planning factors from the rectifier guide |
| Battery autonomy target | 4 hours | At the 180 A design load |
| DoD × ageing factor | 0.8 × 0.9 | Usable fraction of nameplate Ah |
2. Formula and units
I combined (A) = (Iload × (1 + growth) + Irecharge × (1 + recharge peak)) × (1 + headroom)
Required Ah = (Iload × hours) ÷ (DoD × ageing)
Units: amperes (A), ampere-hours (Ah), hours (h).
3. Calculation
| Step | Calculation | Result |
|---|---|---|
| Load with growth | 180 × 1.15 | 207.0 A |
| Recharge with peak | 60 × 1.25 | 75.0 A |
| Combined with headroom | (207 + 75) × 1.15 | 324.3 A |
| Battery Ah for 4 h | (180 × 4) ÷ (0.8 × 0.9) | 1,000 Ah |
4. Result and limits
Plan rectifier capacity around a 324.3 A combined scenario (then apply module size, derating, N+1 and N-1 checks in the calculator). For four hours at 180 A with the stated DoD/ageing factors, nameplate battery capacity is about 1,000 Ah.
Boundaries: does not replace vendor discharge curves, temperature derating, generator test data or maintenance rules. Age, temperature and faults can shorten runtime. Continue with rectifier sizing guide and generator fuel planning.
Common Engineering Scenarios
- Rectifier capacity with recharge and N-1 — size operating and failed-unit states.
- One-tank generator runtime — relate load, fuel curve and required autonomy.
- Site expansion — recalculate DC load, rectifier reserve, battery runtime and generator margin together.
Failure, Resilience and Operations
Check the loss of one rectifier, reduced battery capacity, generator derating and solar shortfall. A nominal capacity result does not prove backup performance during a fault or an aged-battery condition.
Engineering Resources
Use the linked guides and calculator methodology with equipment data sheets, battery discharge curves and site operating rules. Record the load boundary, units, ambient conditions and design margin with each result.
Recommended Learning Path
- Measure and define the DC load boundary.
- Size rectifiers and verify recharge/N-1.
- Calculate battery autonomy at the design load.
- Model generator fuel and solar contribution.
- Review fault states, derating and maintenance constraints.
Engineering Boundaries and FAQ
These browser tools do not replace manufacturer discharge curves, generator test data, temperature derating or an operational maintenance plan. Validate results against the installed equipment and site rules.
Why calculate rectifiers before batteries?
Rectifier reserve and recharge performance define the load that the battery system must support during normal and recovery states.
Does runtime equal guaranteed service time?
No. Runtime is an estimate from supplied load, battery and fuel assumptions; age, temperature, generator loading and faults can reduce it.
Related Topics
Related pages
Network asset lifecycle tracker · Out-of-band network design workshop